New detail up parts for MFH kits or other (ignition coils)

For all F1 scale model news...
Post Reply
User avatar

Topic author
Preludevenom
Top Designer
Top Designer
Posts: 717
Joined: Tue Jul 15, 2014 11:14 am
Status: Offline

New detail up parts for MFH kits or other (ignition coils)

Post by Preludevenom »

Hello,

New 1/12 Ignition coils sets are ready.
1.jpg
Included is:
2x CNC Machined parts
2x 3D printed cap pre.drilled
2x Photoetched tie
2x Rod
4x Photoetched parts
4x 0.15mm cable
6x watchmaker screw
2x 1.6mm shrink tub
4x 1.2mm shrnk tube
2.jpg
3.jpg
Instructions on PDF download.

They can be used on:

-Any 1/12 cars from 50's era that match, no need to be MFH.
-K476+K477+K478 Ferrari 330 P4 open
-K492+K493+K494 Ferrari 330 P4 Close

They can be used on those MFH kits too but they will be included in the upcoming detail up set:

-K537+K538+K539 Ferrari 315/335S
-K548+K549 Ferrari 250TR57

IMPORTANT NOTE: All persons that want the upcoming detail up set for 1/12 Ferrari 250TR 57/58 or 315/335S dont need to buy those as they will be included in the complete set.

SOLD OUT AT THE MOMENT! thank you very much

PM for orders

Thank you very much
Kind regards
Last edited by Preludevenom on Tue Apr 23, 2019 1:57 pm, edited 1 time in total.

jaydar
Constructors Champion
Constructors Champion
Posts: 1242
Joined: Sun Sep 30, 2012 12:09 pm
Status: Offline

Re: New detail up parts for MFH kits or other (ignition coil

Post by jaydar »

There will be a detail set for the 330P4?
What about the 250TR57?

The pieces you have shown look very good.

Regards,

Joe
User avatar

Topic author
Preludevenom
Top Designer
Top Designer
Posts: 717
Joined: Tue Jul 15, 2014 11:14 am
Status: Offline

Re: New detail up parts for MFH kits or other (ignition coil

Post by Preludevenom »

Hi Joe, you have a PM ;)
User avatar

lezdep
FOTA Chairman
FOTA Chairman
Posts: 3619
Joined: Tue Aug 23, 2005 2:42 am
Favorite F1 Team or Driver: Senna
Location: Toronto
Status: Offline
Canada

Re: New detail up parts for MFH kits or other (ignition coil

Post by lezdep »

I would be in for a detail set for P4. I have looked at my kit and I think it definitely will benefit from extra detail parts.
But the thing needed to most for it is better wiring and plumbing instructions. MFH really put in only basic fuel lines and
ignition wires. And just to mention it - P4 needs 4 coils. So, probably make sense to make an detail set which would include
4 from the start.

Btw, I think there was relatively recent discussion on location of battery on P4. I had saved couple of photos from that
thread and battery looks different to that you made for 335S and 250TR.

Anyway, keep doing that great job of making detail parts. They look great.
User avatar

Topic author
Preludevenom
Top Designer
Top Designer
Posts: 717
Joined: Tue Jul 15, 2014 11:14 am
Status: Offline

Re: New detail up parts for MFH kits or other (ignition coil

Post by Preludevenom »

Hi Lezdep,

Thank you very much, i will keep in mind the piping upgrade that could be intresting. Yes the Battery looks very different, but it's not really visible as it's putted under the exhaust in a very special way. so it will be difficult to do something that match the reality..... anyway i will try to figure out something but it will be later on this year.

Thank you very much, ;)

Kind regards
User avatar

Topic author
Preludevenom
Top Designer
Top Designer
Posts: 717
Joined: Tue Jul 15, 2014 11:14 am
Status: Offline

Re: New detail up parts for MFH kits or other (ignition coil

Post by Preludevenom »

All Ignition coils set are sold out at the moment Thank you very much!
Post Reply
  • Similar Topics
    Replies
    Views
    Last post