View topic - Ferrari 312T4

Ferrari 312T4

Models in progress... including non-F1 models.

Re: Ferrari 312T4

Postby Anthony_RUS » Wed Oct 02, 2019 12:02 am

Some progress...

I deleted all supports from 3d-printing parts, little bit sanding those and blow first coat of primer.
Image

In parallel i work with body. At first i replaced grilles. Those were with defects and in general the geometry was wrong.
Image
Image
Image
Image
Image
User avatar
Anthony_RUS
F1 Test Driver
F1 Test Driver
 
Posts: 283
Joined: Sat Sep 05, 2009 9:54 am
Location: Moscow
Favorite F1 Team: Ferrari

Re: Ferrari 312T4

Postby Enzojz » Wed Oct 02, 2019 3:46 pm

Why did you separate 3d printed part for example exhaust, I think it could have been done as a whole :)

PS: for european and north american moders Shapeways get a very good printing quality while the price is relatively low.
Enzojz
F3
F3
 
Posts: 24
Joined: Tue Aug 23, 2016 4:02 pm
Favorite F1 Team: Ferrari

Re: Ferrari 312T4

Postby sky1911 » Wed Oct 02, 2019 6:12 pm

Very likely because cleanup of one big pile of exhaust snakes that are interconnected is basically not possible. There will be areas you cannot reach, no matter what. So it makes sense to print them as separate entities for easier cleanup. That and of course for ease of assembly. One solid piece is harder to fit than separate parts. But those are just my thoughts, why *I* would do it like that.
Cheers,
Roman
User avatar
sky1911
Best of the Rest
Best of the Rest
 
Posts: 572
Joined: Sun Jul 20, 2014 7:28 am
Favorite F1 Team: McLaren

Re: Ferrari 312T4

Postby Anthony_RUS » Thu Oct 03, 2019 12:04 am

sky1911 wrote:Very likely because cleanup of one big pile of exhaust snakes that are interconnected is basically not possible. There will be areas you cannot reach, no matter what. So it makes sense to print them as separate entities for easier cleanup. That and of course for ease of assembly. One solid piece is harder to fit than separate parts. But those are just my thoughts, why *I* would do it like that.



Exactly :D

And another advantage in separate printing is that i can turn every single part in the best position for printing. And because of that, the print quality of the signle parts will be higher than the whole assembly.
User avatar
Anthony_RUS
F1 Test Driver
F1 Test Driver
 
Posts: 283
Joined: Sat Sep 05, 2009 9:54 am
Location: Moscow
Favorite F1 Team: Ferrari

Re: Ferrari 312T4

Postby gp-models » Thu Oct 03, 2019 9:41 am

Lovely attention to details Anthony, still looking great! :)
User avatar
gp-models
FOTA Vice Chairman
FOTA Vice Chairman
 
Posts: 1708
Joined: Sun Oct 07, 2012 2:17 pm
Favorite F1 Team: Mclaren, Ferrari, Williams, Lotus

Re: Ferrari 312T4

Postby Lloyd » Fri Oct 04, 2019 8:08 pm

Those grilles improve the look of the body so much , just awesome if someone released them as a set
Lloyd
A1 GP
A1 GP
 
Posts: 49
Joined: Sat Jun 10, 2017 7:04 pm
Favorite F1 Team: No favourite , just all 1/12 scale F1 kits

Re: Ferrari 312T4

Postby zosc » Sat Oct 05, 2019 10:10 am

if someone released them as a set


I'm praying for this
User avatar
zosc
A1 GP
A1 GP
 
Posts: 34
Joined: Sun Mar 07, 2010 3:56 pm

Re: Ferrari 312T4

Postby Redbox » Wed Oct 09, 2019 3:45 am

Hi Anthony, great job with 3d printed parts.
I would ask you which glue are you using to bond 3D printed resin parts.
Gluing Abs or Pla is not difficult, but printed resin is more tricky.

Thank you!
Redbox
Spectator
Spectator
 
Posts: 6
Joined: Wed Jul 24, 2019 9:20 am

Re: Ferrari 312T4

Postby Anthony_RUS » Thu Oct 10, 2019 8:09 am

Thanks!

Redbox wrote:I would ask you which glue are you using to bond 3D printed resin parts.


I use cyanoacrylate glue - Cosmofen CA 12
User avatar
Anthony_RUS
F1 Test Driver
F1 Test Driver
 
Posts: 283
Joined: Sat Sep 05, 2009 9:54 am
Location: Moscow
Favorite F1 Team: Ferrari

Re: Ferrari 312T4

Postby Anthony_RUS » Fri Oct 18, 2019 3:24 pm

Wings are painted

Image
Image
User avatar
Anthony_RUS
F1 Test Driver
F1 Test Driver
 
Posts: 283
Joined: Sat Sep 05, 2009 9:54 am
Location: Moscow
Favorite F1 Team: Ferrari

PreviousNext

Return to Work in Progress



Who is online

Users browsing this forum: No registered users and 8 guests

cron