Warning for Beemax Lancia S4
-
Topic author - Constructors Champion
- Posts: 1381
- Joined: Thu May 01, 2008 11:04 am
- Location: HOT California, USA
- Status: Offline
Warning for Beemax Lancia S4
This kit is one warning after the other. I was able to overcome all but this last one. I would SWEAR I used the extra "cab" piece that Beemax gave us 2 of. Whichever the hell one I used, the windscreen comes no where near fitting. My recommendation to all who have this kit is to dry fit the windscreen to both cabs, take the one that it doesn't fit to and immediatley toss it in the trash. WHY they included 2 pieces......i'm not interested in discussing. I am SO disappointed. I really wanted to like this kit and I really do not.
Other problems: you must soak decals in damn near hot water for a minute. If not, they will stretch when coming off the paper. And even once in place, if you try brushing the excess water away, the decal will distort.
The placement for the footwell carbons is all wrong.
I found that I needed to make all guide holes bigger.
I am fairly certain the instructions for the front end with the radiator, etc, is incorrect. None of those pieces fit well at all.
I sliced my finger on the very thick PE parts while trying to fold it over a block. You need a specific tool to fold these.
Getting the front bonnet onto its little hinge was quite difficult and once it was on, it didn't fit the car properly.
Good luck.
Other problems: you must soak decals in damn near hot water for a minute. If not, they will stretch when coming off the paper. And even once in place, if you try brushing the excess water away, the decal will distort.
The placement for the footwell carbons is all wrong.
I found that I needed to make all guide holes bigger.
I am fairly certain the instructions for the front end with the radiator, etc, is incorrect. None of those pieces fit well at all.
I sliced my finger on the very thick PE parts while trying to fold it over a block. You need a specific tool to fold these.
Getting the front bonnet onto its little hinge was quite difficult and once it was on, it didn't fit the car properly.
Good luck.
Last edited by bossy122 on Sat Jun 22, 2019 3:04 am, edited 2 times in total.
Re: Warning for Beemax Lancia S4
Wow. Just wow.
Re: Warning for Beemax Lancia S4
I thought exactly the same!AJP01 wrote:Wow. Just wow.
-
- FOTA Chairman
- Posts: 4438
- Joined: Wed Dec 21, 2005 3:20 pm
- Favorite F1 Team or Driver: Stake Sauber
- Location: Oulu-Uleåborg Finland
- Status: Offline
Re: Warning for Beemax Lancia S4
Sith happens .
My completed Models:
https://www.flickr.com/photos/150229040 ... 3349714787
https://www.flickr.com/photos/150229040 ... 3349714787
Re: Warning for Beemax Lancia S4
Er.... so, let's see: not only did they reinforce the roof (or that's what was supposed to) but they put windscreen with a higher angle (maybe they got it wrong at first try?) as happend with new versions of Sprt Quattro.
Or maybe the roof is now a bit lower at the front? maybe both.
Ahem, then what I fear is that windows will also have a hard time to fit the door... have yu tried?
Thanks for the report!
Or maybe the roof is now a bit lower at the front? maybe both.
Ahem, then what I fear is that windows will also have a hard time to fit the door... have yu tried?
Thanks for the report!
-
- FOTA Chairman
- Posts: 2271
- Joined: Sun Jul 30, 2006 4:27 pm
- Location: Barnsley, UK
- Status: Offline
Re: Warning for Beemax Lancia S4
Is that first picture showing the front cowling fit the actual fit? With that huge gap there? If so you've got something wrong. I've seen pictures of the built up kit on other forums and there wasn't any gap like that..
Steve Noble
-
Topic author - Constructors Champion
- Posts: 1381
- Joined: Thu May 01, 2008 11:04 am
- Location: HOT California, USA
- Status: Offline
Re: Warning for Beemax Lancia S4
SteveNoble wrote:Is that first picture showing the front cowling fit the actual fit? With that huge gap there? If so you've got something wrong. I've seen pictures of the built up kit on other forums and there wasn't any gap like that..
I went back and took that hinge piece off figuring i'd just mount the "hood" on and the 2 guide holes at the dash area were off enough that that wasnt really a solution either. I put the 2 cabs side by side and the one not used is just that bit longer at the dash, which would make the hood fit. The side glass fits perfectly on both cabs.
-
- FOTA Chairman
- Posts: 2271
- Joined: Sun Jul 30, 2006 4:27 pm
- Location: Barnsley, UK
- Status: Offline
Re: Warning for Beemax Lancia S4
I also got two body parts in the box. One of them was all squashed and not usable. The other was fine. I've just test fitted the front and middle parts together and the fit on my example seems very good.
Steve Noble
-
- FOTA Chairman
- Posts: 2271
- Joined: Sun Jul 30, 2006 4:27 pm
- Location: Barnsley, UK
- Status: Offline
Re: Warning for Beemax Lancia S4
Just measured the windscreen on mine and it fits perfectly on both middle body sections, even the squashed on, which was only squashed at the back by the way. Looking at both the supplied middle body sections I can't actually see any noticable difference between the two. I've also seen a few of these built up, as I said, on other forums and nobody mentioned any fit problems. Also most people praised the decals, saying they went on perfectly..
Steve Noble
-
Topic author - Constructors Champion
- Posts: 1381
- Joined: Thu May 01, 2008 11:04 am
- Location: HOT California, USA
- Status: Offline
Re: Warning for Beemax Lancia S4
Remember, the hood is mounted to the front of the chassis, not the cab.